Cyclades AlterPath Manager 5000 Bedienungsanleitung PDF herunterladen

This guide provides a summary of basic AlterPath™ Manager installation tasks for installers who

already know how to install and configure Cyclades AlterPath products.

The following table lists basic tasks in the order they should be performed. For more-detailed

procedures, go to the listed page numbers.

1. Rack Mounting the AlterPath Manager

For the AlterPath Manager E2000, 2500 and 5000, two brackets and the necessary mounting

screws are supplied. For the AlterPath Manager 2500 and 5000, a set of sliding rails are also

provided (the small “ear” brackets are already attached).

T To Bracket Mount an APM

1. Attach the mounting brackets to the sides of the APM E2000 towards the front of the box. Use

a screwdriver to firmly tighten the mounting brackets (already attached to the APM 2500 and

APM 5000).

2. Mount the APM securely to the vertical bars of the rack. Screws should go in through the front

of the brackets into the outside front of the vertical bars. Be sure to locate the APM so the

brackets line up correctly with the holes. Be sure the right and left brackets are at the same

height.

T To Rail Mount an APM 2500 or 5000

1. Remove the inner rails from the rail assemblies. Slide each inner rail out until it stops. Then

depress the exposed locking tab to unlock the inner rail and slide it out the rest of the way.

2. Attach the inner rails to the sides of the APM 2500 or APM 5000. When the inner rails are

correctly positioned, the tabs will be to the rear of the APM, and the front three holes in the

inner rails will line up with the holes in the sides of the APM.

3. Attach the outer rails to the rack, using the end brackets. Be sure the open end of each outer

rail is located towards the front of the rack.

1. Rack Mounting the AlterPath Manager Page 1

To Bracket Mount an APM Page 1

To Rail Mount an APM 2500 or 5000 Page 1

2 Making the Ethernet Connection Page 2

To Set up a Single Network Page 3

To Set up a Private Network Page 4

3 Running the First Time Configuration Wizard Page 5

4 Connecting to the Web Management Interface (WMI) Page 8

AlterPath™ Manager

E2000, 2500, and 5000

QuickStart Guide

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - QuickStart Guide

This guide provides a summary of basic AlterPath™ Manager installation tasks for installers who already know how to install and configure Cyclades Alt

Seite 2

AlterPath Manager E2000, 2500, 5000 Quick Start Guide2a. The shorter end brackets mount onto the front of the outer rails. Use the two round screw hol

Seite 3 - To Set up a Single Network

2. Making the Ethernet Connection3Figure 5: APM 5000 Front View with Control ButtonsFigure 6: APM 5000 Rear View with Ports and Power ConnectorThere a

Seite 4 - To Set up a Private Network

AlterPath Manager E2000, 2500, 5000 Quick Start Guide4 Figure 7: Single Network SetupT To Set up a Private Network1. Connect an Ethernet cable from th

Seite 5

3. Running the First Time Configuration Wizard5.Figure 8: Private Network Setup3. Running the First Time Configuration WizardThe First Time Configurat

Seite 6

AlterPath Manager E2000, 2500, 5000 Quick Start Guide6• No parity• 1 stop bit• ANSI emulation4. Power on the APMBoot information will scroll up on the

Seite 7

3. Running the First Time Configuration Wizard73) 10 Mbps, half duplex4) 100 Mbps, full duplex5) 100 Mbps, half duplex6) 1000 Mbps, full duplex7) 1000

Seite 8

AlterPath Manager E2000, 2500, 5000 Quick Start Guide Cyclades Corporation3541 Gateway BoulevardFremont, CA 94538 USA1.888.CYCLADES (292.5233)1.510.77

Kommentare zu diesen Handbüchern

Keine Kommentare

Cyclades AlterPath Manager 5000 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Cyclades AlterPath Manager 5000 herunter. Cyclades AlterPath Manager 5000 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Cyclades AlterPath Manager 5000